970-945-7777

  

 


Reid Racing HD Steering Knuckles and C's for Dana 60

We have these:
So you don't end up with this:

 

  • The strongest Dana 60 knuckles on the market
     
  • Cast from high strength ductile iron
     
  • Beefed up with extra material and ribbing
     
  • 100% interchangeable with a Chevy kingpin knuckle
     
  • 5th bolt hole for high steer arms (4 bolt arms still fit)
     
  • Cast in steering stop eliminates bent stop bolts
     
  • Tapered tie rod hole for 1 ton ends
     
  • Tie rod holes can be drilled to accept 3/4" rod end
     
  • Powder coated bright orange for long lasting looks
     
  • Fully machined and ready for installation
     
  • Available for Chevy/Dodge and Ford
     
Application
Side
Notes
Price

GM kingpin Dana 60

Driver's side knuckle

Direct interchange on GM D60's

Fits Dodge D60 if used in pairs, the Dodge tie rod arm is at a slightly different height than the GM so using one OE knuckle and one Reid knuckle on a Dodge D60 leaves the tie rod at an angle


$299 

GM kingpin Dana 60
 

Passenger's side knuckle

Direct interchange on GM D60's

Fits Dodge D60 if used in pairs, the Dodge tie rod arm is at a slightly different height than the GM so using one OE knuckle and one Reid knuckle on a Dodge D60 leaves the tie rod at an angle

$299
'77-'79 Ford kingpin Dana 60
Driver's side knuckle

Ford kingpin Dana 60 driver's side knuckle, direct swap on 77-79 Ford D60's. 

These fit 85-91 Ford Dana 60's but these knuckles are setup with a larger taper than stock, so they need to be replaced in pairs on those axles and a new tie rod with the larger ends must be used (we can supply that) or you can re-taper the knuckles to match the taper.

These are not a direct replacment for OE Ford knuckles. They must be installed in pairs.

$329
'77-'79 Ford kingpin Dana 60
Passenger's side knuckle

Ford kingpin Dana 60 driver's side knuckle, direct swap on 77-79 Ford D60's. 

These fit 85-91 Ford Dana 60's but these knuckles are setup with a larger taper than stock, so they need to be replaced in pairs on those axles and a new tie rod with the larger ends must be used (we can supply that) or you can re-taper the knuckles to match the taper.

These are not a direct replacment for OE Ford knuckles. They must be installed in pairs.

$329
         
 
 


 

 


 

 

 

D60 inner C

  • Sold individually - please specify part number (tube diameter) when ordering
  • The strongest Dana 60 Inner "C"s on the market
  • The only new FORGED kingpin Dana 60 "C"s on the market
  • Heat-treated for extra strength
  • Available for 3", 3-1/8" and 3-1/2" tube sizes
  • Can be custom bored (up to 3-5/8") using the fixturing ring machined on the "C"
  • Ideal for new builds, narrowing or hybrid axles
  • Forging based on the huge Dana 70 inner "C"
  • Much stronger than factory Dana 60 "C"s
  • Powder coated bright orange for long lasting looks
  • Interchangeable with all factory and aftermarket Kingpin Dana 60 components

 

Available for 3", 3-1/8" and 3-1/2" tubes




$329 each

 

Choose the category you would like more information on.

Doubler™ Dual Transfer Case
Swaybar Correction/Disconnect™ Kit
Shackle Flip™ Kit for ‘67-up GM trucks
Bolt-In Steering Box Brace Kit
1" Body Lift Kit
Competition Style Motor Mounts
Heavy Duty Front Shackles
Chrome Moly Front Axle Shafts
Drivetrain Upgrades
Blazer Soft Tops

Greasable Rear Suspension Bushings
Swaybar Bushing Kits
Body Mounts
Transfer case mounts
Front Upper Shackle Bushing Kit
Spring Bushings
Competition Style Bumpstops
Bushing Assemblies
Tuff Country Suspension